13 Choose one of the image buttons for scanning test.
14 Place your image on the scanner bed.
15 Insert your document into the ADF, ready for scan.
16 1. Place your TMA template on the scanner with the correct orientation.\n2. Place a transparency film or slide inside the template.
17 Place your transparency flim or slide for scanning.
64 1001 The MS-PNR driver is not installed.
65 1002 Unable to install the MS-PNR card.
67 1003 Unable to install the MS-PCZ card
68 2001 Scanner is not connected.
69 2002 Scanner not ready.
70 0004 Memory is not enough for running ScanTest.
71 9001 Unidentified error.
72 0001 Unsupported interface card detected.
73 0005 Hard disk space is not enough for using other applications.
74 6002 ADF paper jammed.
75 2003 ADF paper out.
76 6003 Scanner door sensor failure.
77 0002 The MS-PNR card is missing.
78 0003 The MS-PCZ card is missing.
79 6004 External 12V DC power adpater failure.
96
97 Check the I/O port status for all of the interface cards installed in your PC. \n\nCheck to see if they occupy these ports:\n\n 779H,379H,360H,280H,290H,300H,\n 310H,330H,340H,348H,350H
99 The J1 jumper block should match with the base memory address,\nexclude this range from the extended/expanded memory.\n Example:\n DEVICE=EMM386 X=D400-D7FF
100 Step:\n\n1. Check cable connections.\n2. Check to see if a SCSI terminator is required.\n3. Check to see if the READY indicator and the scannig lamp are both stay lit.\n4. Make sure there is no SCSI ID number conflict.
101 Step:\n\n1. Check cable connections.\n2. Check to see if a SCSI terminator is required.\n3. Check to see if the READY indicator and the scannig lamp are both stay lit.\n4. Click the Retry button to try it again.
102 Close unuseful applications to free up more available memory. Minimum 1 MB memory is required.
103 Step:\n\n1. Check to see there is no SCSI ID number conflict.\n2. Check the SCSI cable connections.\n3. Run ScanTest again.
104 1. Make sure the MS-PNR, MS-PCZ or ASPI interface card is installed.\n\n2.Modify the 'Interface' string in the [SCANNER] section in MSCANDC.INI in Windows directory\n Interface=PNR ,=SCSI or =ASPI
105 Minimum 5 MB hard disk space is required for operation.
106 Remove the jammed paper.
107 Place your document into ADF.
108 Close the scanner door.
109 Make sure the MS-PNR card is installed. \n If not, power off your PC and install it.
110 Make sure the MS-PCZ card is installed. \nIf not, power off your PC and install the MS-PCZ.\nThe J1 jumper block should match with the base memory address, exclude this range from the extended/expanded memory.\n Example:\n \n DEVICE=EMM386 X=D400-D7FF
111 Apply the external 12V DC power.\nOr call your Microtek dealer for help.
128 Step:\n\n1. Power off your scanner.\n2. Close Windows and power off PC.\n3. Power up PC first, and then turn on scanner power until the READY indicator is lit.\n4. Run ScanTest again.\n\n5. If this problem still exists, ca \nll your Microtek scanner dealer.
129 \n6. Make sure the TMA calibration window is not masked. Using the right template, place a trasparency film inside the template.
130 VMIISD.VXD does not exist. Please reinstall ScanWizard again.
131 \n\n** Make Sure the scanner is on the list of the system device manager.
